- 您现在的位置：买卖IC网 > Sheet目录370 > ZXLD1360ET5TA (Diodes Inc)IC LED DRIVR WHITE BCKLGT TSOT-5
A Product Line of
Diodes Incorporated
ZXLD1360
Application Information (cont.)
Layout Considerations
LX pin
The LX pin of the device is a fast switching node, so PCB tracks should be kept as short as possible. To minimize ground
'bounce', the ground pin of the device should be soldered directly to the ground plane.
Coil and decoupling capacitors and current sense resistor
It is particularly important to mount the coil and the input decoupling capacitor as close to the device pins as possible to
minimize parasitic resistance and inductance, which will degrade efficiency. It is also important to minimize any track
resistance in series with current sense resistor R S . Its best to connect VIN directly to one end of R S and Isense directly to the
opposite end of RS with no other currents flowing in these tracks. It is important that the cathode current of the Schottky
diode does not flow in a track between R S and V IN as this may give an apparent higher measure of current than is actual
because of track resistance.
ADJ pin
The ADJ pin is a high impedance input for voltages up to 1.35V so, when left floating, PCB tracks to this pin should be as
short as possible to reduce noise pickup. A 100nF capacitor from the ADJ pin to ground will reduce frequency modulation of
the output under these conditions. An additional series 10k ? resistor can also be used when driving the ADJ pin from an
external circuit (see below). This resistor will provide filtering for low frequency noise and provide protection against high
voltage transients.
10k
100nF
ADJ
ZXLD1360
GND
GND
High voltage tracks
Avoid running any high voltage tracks close to the ADJ pin, to reduce the risk of leakage currents due to board contamination.
The ADJ pin is soft-clamped for voltages above 1.35V to desensitize it to leakage that might raise the ADJ pin voltage and
cause excessive output current. However, a ground ring placed around the ADJ pin is recommended to minimize changes in
output current under these conditions.
Evaluation PCB
A number of ZXLD1360 evaluation boards are available on request for qualified opportunities.
For example:
ZXLD1360EV11 MR16 replacement interfaces to external LED.
The evaluation boards allow quick testing of the ZXLD1360 and provide a simple way of connecting external LEDs.
ZXLD1360
Document number: DS33471 Rev. 4 - 2
21 of 25
www.diodes.com
March 2011
? Diodes Incorporated
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
ZXLD1362ET5TA
IC LED DRIVR WHITE BCKLGT TSOT-5
ZXLD1366DACTC
IC LED DRIVER WHITE BCKLGT 6-DFN
ZXLD1370EST16TC
IC LED DRVR HIGH BRIGHT TSSOP-16
ZXLD1371QESTTC
IC LED DRIVER
ZXLD1374EST20TC
IC LED DVR BUCK BOOST 20TSSOP
ZXLD1937ET5TA
IC LED DRIVR WHITE BCKLGT TSOT-5
ZXLD381FHTA
IC LED DRIVR WHITE BCKLT SOT23-3
ZXLD383ET5TA
IC LED DRIVR WHITE BCKLGT TSOT-5
相关代理商/技术参数
ZXLD1360ET5TA-CUT TAPE
制造商:DIODES 功能描述:ZXLD1360 Series 1 A 1 MHz SMT LED Driver with Internal Switch - TSOT-23-5
ZXLD1362
制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:60V 1A LED DRIVER WITH AEC-Q100
ZXLD1362_12
制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:60V 1A LED DREIVER WITH AEC-Q100
ZXLD1362ET5TA
功能描述:LED照明驱动器 1A/60V LED DRIVER RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
ZXLD1362ET5TA-CUT TAPE
制造商:DIODES 功能描述:ZXLD1362 Series 1 A 1 MHz SMT LED Driver with Internal Switch - TSOT-23-5
ZXLD1366
制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:High accuracy 1A, 60V LED driver with internal switch
ZXLD1366_10
制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:HIGH ACCURACY 1A, 60V LED DRIVER WITH INTERNAL SWITCH
ZXLD1366DACTC
功能描述:LED照明驱动器 1A, 60V LED Drver, Int Swtch RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N